9.4.1.2 Packet Tracer – Skills Integration Challenge - Instructions Answers

Certification Answers

Packet Tracer – Skills Integration Challenge (Instructor Version)

Instructor Note: Red font color or gray highlights indicate text that appears in the Answer copy only.

Topology

Addressing Table

VLANs and Port Assignments Table

Scenario

This culminating activity includes many of the skills that you have acquired during this course. First, you will complete the documentation for the network. Make sure you have a printed version of the instructions. During implementation, you will configure VLANs, trunking, port security and SSH remote access on a switch. You will then implement inter-VLAN routing and NAT on a router. Finally, you will use your documentation to verify your implementation by testing end-to-end connectivity.

Documentation

You are required to fully document the network. You will need a print out of this instruction set, which will include an unlabeled topology diagram:

  • Label all the device names, network addresses and other important information that Packet Tracer generated.
  • Complete the Addressing Table and VLANs and Port Assignments Table.
  • Fill in any blanks in the Implementation and Verification steps. The information is supplied when you launch the Packet Tracer activity.

Implementation

Note: All devices in the topology except [[R1Name]][[S1Name]], and [[PC1Name]] are fully configured. You do not have access to the other routers. You can access all the servers and PCs for testing purposes.

Implement to following requirements using your documentation:

[[S1Name]]

  • Configure remote management access including IP addressing and SSH:
    • Domain is cisco.com
    • User [[UserText]] with password [[UserPass]]
    • Crypto key length of 1024
    • SSH version 2, limited to 2 authentication attempts and a 60 second timeout using the following commands:
      • ip ssh version 2
      • ip ssh authentication-retries 2
      • ip ssh time-out 60
    • Clear text passwords should be encrypted.
  • Configure, name and assign VLANs. Ports should be manually configured as access ports.
  • Configure trunking.
  • Implement port security:
    • On F0/1, allow 2 MAC addresses that are automatically added to the configuration file when detected. The port should not be disabled, but a syslog message should be captured if a violation occurs.
    • Disable all other unused ports.

[[R1Name]]

  • Configure inter-VLAN routing.
  • Configure DHCP services for VLAN 30. Use LAN as the case-sensitive name for the pool.
  • Implement routing:
    • Use RIPv2 as the routing protocol.
    • Configure one network statement for the entire [[DisplayNet]] address space.
    • Disable interfaces that should not send RIPv2 messages.
    • Configure a default route to the Internet.
  • Implement NAT:
    • Configure a standard, one statement ACL number 1. All IP addresses belonging to the [[DisplayNet]] address space are allowed.
    • Refer to your documentation and configure static NAT for the File Server.
    • Configure dynamic NAT with PAT using a pool name of your choice, a /30 mask, and these two public addresses:

[[NATPoolText]]

[[PC1Name]]

Verify [[PC1Name]] has received full addressing information from [[R1Name]].

Verification

All devices should now be able to ping all other devices. If not, troubleshoot your configurations to isolate and solve problems. A few tests include:

  • Verify remote access to [[S1Name]] by using SSH from a PC.
  • Verify VLANs are assigned to appropriate ports and port security is in force.
  • Verify RIP neighbors and a complete routing table.
  • Verify NAT translations and statics.
    • Outside Host should be able to access File Server at the public address.
    • Inside PCs should be able to access Web Server.
  • Document any problems you encountered and the solutions in the Troubleshooting Documentation table below.

Troubleshooting Documentation

Suggested Scoring Rubric

Packet Tracer scores 70 points. Documentation is worth 30 points.

ID:[[indexAdds]][[indexNames]]

*****************************************************
ISOMORPH ID KEY:
ID = XY where;
X = indexAdds for /24 private address space
Y = indexNAMES for device names
Note: Each seed contains variables that are independent
of the other seeds. You do not need to test all the various combinations.

=======================================================
 ISOMORPH ID = 00
 =======================================================
 !HQ!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 en
 conf t
 ip dhcp pool LAN
 network 172.16.15.32 255.255.255.224
 default-router 172.16.15.33
 interface GigabitEthernet0/0
 no shutdown
 interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 172.16.15.17 255.255.255.240
 ip nat inside
 interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 172.16.15.33 255.255.255.224
 ip nat inside
 interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 172.16.15.1 255.255.255.248
 interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 172.16.15.9 255.255.255.248
 router rip
 version 2
 passive-interface GigabitEthernet0/0
 passive-interface Serial0/1/0
 network 172.16.0.0
 !
 ip nat pool TEST 209.165.200.225 209.165.200.226 netmask 255.255.255.252
 ip nat inside source list 1 pool TEST overload
 ip nat inside source static 172.16.15.18 209.165.200.227
 ip route 0.0.0.0 0.0.0.0 Serial0/1/0
 access-list 1 permit 172.16.15.0 0.0.0.255
 interface s0/0/0
 ip nat inside
 interface s0/0/1
 ip nat inside
 interface s0/1/0
 ip nat outside
 end
 wr
!!!!!!!!!!!!!!!!!!!!!!!!
 !HQ-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 !
 en
 conf t
 int vlan 60
 ip add 172.16.15.10 255.255.255.248
 no shut
 ip default-gateway 172.16.15.9
 vlan 15
 name Servers
 vlan 30
 name PCs
 vlan 45
 name Native
 vlan 60
 name Management
 interface range fa0/1 - 10
 switchport mode access
 switchport access vlan 30
 interface fa0/1
 switchport port-security
 switchport port-security maximum 2
 switchport port-security mac-address sticky
 switchport port-security violation restrict
 interface range fa0/11 - 20
 switchport mode access
 switchport access vlan 15
 interface g0/1
 switchport mode trunk
 switchport trunk native vlan 45
 interface range fa0/21 - 24 , g0/2
 shutdown
 ip domain-name cisco.com
 crypto key gen rsa
 1024
 user HQadmin pass ciscoclass
 service password-encryption
 ip ssh version 2
 ip ssh auth 2
 ip ssh time 60
 line vty 0 15
 login local
 transport input ssh
=======================================================
 ISOMORPH ID = 11
 =======================================================
 !Admin!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 en
 conf t
 ip dhcp pool LAN
 network 10.10.10.192 255.255.255.192
 default-router 10.10.10.193
 interface GigabitEthernet0/0
 no shutdown
 interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 10.10.10.161 255.255.255.224
 ip nat inside
 interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 10.10.10.193 255.255.255.192
 ip nat inside
 interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 10.10.10.129 255.255.255.240
 interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 10.10.10.145 255.255.255.240
 router rip
 version 2
 passive-interface GigabitEthernet0/0
 network 172.16.0.0
 interface s0/0/0
 ip nat inside
 interface s0/0/1
 ip nat inside
 interface s0/1/0
 ip nat outside
 !
 ip nat pool TEST 198.133.219.128 198.133.219.129 netmask 255.255.255.252
 ip nat inside source list 1 pool TEST overload
 ip nat inside source static 10.10.10.162 198.133.219.130
 ip route 0.0.0.0 0.0.0.0 Serial0/1/0
 access-list 1 permit 10.10.10.0 0.0.0.255
 end
 wr
!!!!!!!!!!!!!!!!!!!!!!!!
 !Admin-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 en
 conf t
 int vlan 60
 ip add 10.10.10.146 255.255.255.240
 no shut
 ip default-gateway 10.10.10.145
 vlan 15
 name Servers
 vlan 30
 name PCs
 vlan 45
 name Native
 vlan 60
 name Management
 interface range fa0/1 - 10
 switchport mode access
 switchport access vlan 30
 interface fa0/1
 switchport port-security
 switchport port-security maximum 2
 switchport port-security mac-address sticky
 switchport port-security violation restrict
 interface range fa0/11 - 20
 switchport mode access
 switchport access vlan 15
 interface g0/1
 switchport mode trunk
 switchport trunk native vlan 45
 interface range fa0/21 - 24 , g0/2
 shutdown
 ip domain-name cisco.com
 crypto key gen rsa
 1024
 user Admin pass letmein
 service password-encryption
 ip ssh version 2
 ip ssh auth 2
 ip ssh time 60
 line vty 0 15
 login local
 transport input ssh
===============================================================
 ISOMORPH ID: 22
 ===============================================================
 !Central!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 en
 conf t
 ip dhcp pool LAN
 network 192.168.45.128 255.255.255.192
 default-router 192.168.45.129
 interface GigabitEthernet0/0
 no shutdown
 interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 192.168.45.65 255.255.255.192
 ip nat inside
 interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 192.168.45.129 255.255.255.192
 ip nat inside
 interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 192.168.45.17 255.255.255.240
 interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 192.168.45.33 255.255.255.240
 router rip
 version 2
 passive-interface GigabitEthernet0/0
 network 172.16.0.0
 interface s0/0/0
 ip nat inside
 interface s0/0/1
 ip nat inside
 interface s0/1/0
 ip nat outside
 !
 ip nat pool TEST 64.100.32.56 64.100.32.57 netmask 255.255.255.252
 ip nat inside source list 1 pool TEST overload
 ip nat inside source static 192.168.45.66 64.100.32.58
 ip route 0.0.0.0 0.0.0.0 Serial0/1/0
 access-list 1 permit 192.168.45.0 0.0.0.255
 end
 wr
!!!!!!!!!!!!!!!!!!!!!!!!
 !Cnt-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 en
 conf t
 int vlan 60
 ip add 192.168.45.34 255.255.255.240
 no shut
 ip default-gateway 192.168.45.33
 vlan 15
 name Servers
 vlan 30
 name PCs
 vlan 45
 name Native
 vlan 60
 name Management
 interface range fa0/1 - 10
 switchport mode access
 switchport access vlan 30
 interface fa0/1
 switchport port-security
 switchport port-security maximum 2
 switchport port-security mac-address sticky
 switchport port-security violation restrict
 interface range fa0/11 - 20
 switchport mode access
 switchport access vlan 15
 interface g0/1
 switchport mode trunk
 switchport trunk native vlan 45
 interface range fa0/21 - 24 , g0/2
 shutdown
 ip domain-name cisco.com
 crypto key gen rsa
 1024
 user CAdmin pass itsasecret
 service password-encryption
 ip ssh version 2
 ip ssh auth 2
 ip ssh time 60
 line vty 0 15
 login local
 transport input ssh