3.2.2.8 Lab – Troubleshoot PPPoE (Instructor Version)
Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only.
Topology

Addressing Table
Device | Interface | IP Address | Subnet Mask | Default Gateway |
---|---|---|---|---|
Cust1 | G0/1 | Learned via PPP | Learned via PPP | Learned via PPP |
ISP | G0/1 | N/A | N/A | N/A |
Objectives
- Part 1: Build the Network
- Part 2: Troubleshoot PPPoE on Cust1
Background / Scenario
ISPs sometimes use Point-to-Point Protocol over Ethernet (PPPoE) on DSL links to their customers. PPP supports the assignment of IP address information to a device at the remote end of a PPP link. More importantly, PPP supports CHAP authentication. ISPs can check accounting records to see if a customer’s bill has been paid, before letting them connect to the Internet.
In this lab, you will troubleshoot the Cust1 router for PPPoE configuration problems.
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.
Note: Ensure that the routers and switches have been erased and have no startup configurations. If you are unsure, contact your instructor.
Instructor Note: Refer to the Instructor Lab Manual for the procedures to initialize and reload devices.
Required Resources
- 2 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
- 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)
- Console cables to configure the Cisco IOS devices via the console ports
- Ethernet cables as shown in the topology
Part 1: Build the Network
Step 1: Cable the network as shown in the topology.
Step 2: Initialize and reload the routers and switches.
Step 3: Copy the configurations on to routers.
a. Copy and paste the Cust1 configuration to the Cust1 router.
hostname Cust1 enable secret class no aaa new-model no ip domain lookup interface GigabitEthernet0/1 no ip address duplex auto speed auto pppoe enable group global pppoe-client dial-pool-number 1 no shut interface Dialer1 mtu 1492 ip address negotiated encapsulation ppp dialer pool 1 ppp authentication chap callin ppp chap hostname Cust1 ppp chap password 0 ciscoppp ip route 0.0.0.0 0.0.0.0 Dialer1 banner motd ^C Unauthorized Access Prohibited. ^C line con 0 password cisco logging synchronous login line aux 0 line vty 0 4 password cisco login end
b. Copy and paste the ISP configuration to the ISP router.
hostname ISP enable secret class username Cust1 password 0 ciscopppoe bba-group pppoe global virtual-template 1 interface GigabitEthernet0/1 no ip address duplex auto speed auto pppoe enable group global no shut interface Virtual-Template1 ip address 10.0.0.254 255.255.255.0 mtu 1492 peer default ip address pool PPPoEPOOL ppp authentication chap callin ip local pool PPPoEPOOL 10.0.0.1 10.0.0.10 ip forward-protocol nd banner motd ^C Unauthorized Access Prohibited. ^C line con 0 password cisco logging synchronous login line vty 0 4 password cisco login end
Note: Many of the ISP router PPPoE configuration commands are beyond the scope of the course.
c. Save the router configurations.
Part 2: Troubleshoot PPPoE on Cust1
In Part 2, you will troubleshoot PPPoE on the Cust 1 router. The privileged EXEC mode password is class, and console and vty passwords are cisco. The ISP has provided a username of Cust1 and a password of ciscopppoe for PPPoE CHAP authentication.
The following log messages should be appearing on your console session to Cust1:
Cust1# *Nov 5 22:53:46.999: %DIALER-6-BIND: Interface Vi2 bound to profile Di1 *Nov 5 22:53:47.003: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up *Nov 5 22:53:47.035: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1 *Nov 5 22:53:47.039: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down Cust1#
Step 1: Verify that IPv4 Address is assigned to the Cust1 Dialer interface.
The Dialer virtual interface did not receive an IP address.
Cust1# show ip interface brief Interface IP-Address OK? Method Status Protocol Embedded-Service-Engine0/0 unassigned YES unset administratively down down GigabitEthernet0/0 unassigned YES unset administratively down down GigabitEthernet0/1 unassigned YES unset up up Serial0/0/0 unassigned YES unset administratively down down Serial0/0/1 unassigned YES unset administratively down down Dialer1 unassigned YES manual up up Virtual-Access1 unassigned YES unset up up Virtual-Access2 unassigned YES unset down down
Step 2: Debug PPP to determine if the problem is with authentication.
a. Turn on debug for PPP authentication.
Cust1# debug ppp authentication PPP authentication debugging is on Cust1# *Nov 5 23:09:00.283: %DIALER-6-BIND: Interface Vi2 bound to profile Di1 *Nov 5 23:09:00.287: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up *Nov 5 23:09:00.287: Vi2 PPP: Using dialer call direction *Nov 5 23:09:00.287: Vi2 PPP: Treating connection as a callout *Nov 5 23:09:00.287: Vi2 PPP: Session handle[8A000036] Session id[54] *Nov 5 23:09:00.315: Vi2 PPP: No authorization without authentication *Nov 5 23:09:00.315: Vi2 CHAP: I CHALLENGE id 1 len 24 from "ISP" *Nov 5 23:0 Cust1#9:00.315: Vi2 PPP: Sent CHAP SENDAUTH Request *Nov 5 23:09:00.315: Vi2 PPP: Received SENDAUTH Response FAIL *Nov 5 23:09:00.315: Vi2 CHAP: Using hostname from interface CHAP *Nov 5 23:09:00.315: Vi2 CHAP: Using password from interface CHAP *Nov 5 23:09:00.315: Vi2 CHAP: O RESPONSE id 1 len 26 from "Cust1" *Nov 5 23:09:00.315: Vi2 CHAP: I FAILURE id 1 len 25 msg is "Authentication failed" *Nov 5 23:09:00.315: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1 *Nov 5 23:09:00.319: %LINK-3 Cust1#-UPDOWN: Interface Virtual-Access2, changed state to down Cust1#
b. End debug mode.
Cust1# u all All possible debugging has been turned off Cust1#
Step 3: Verify that the PPPoE username and password matches what was given by the ISP.
a. Display the running configuration; apply a filter to display only the Dialer section. Verify that the username and password matches what was provided by the ISP.
Cust1# show run | section Dialer interface Dialer1 mtu 1492 ip address negotiated encapsulation ppp dialer pool 1 ppp authentication chap callin ppp chap hostname Cust1 ppp chap password 0 ciscoppp ip route 0.0.0.0 0.0.0.0 Dialer1
b. The problem appears to be with the password. Enter Global configuration mode and fix the ppp password.
Cust1# conf t Enter configuration commands, one per line. End with CNTL/Z. Cust1(config)# interface Dialer1 Cust1(config-if)# ppp chap password ciscopppoe Cust1(config-if)# end Cust1# *Nov 5 23:42:07.343: %SYS-5-CONFIG_I: Configured from console by console Cust1# *Nov 5 23:42:25.039: %DIALER-6-BIND: Interface Vi2 bound to profile Di1 *Nov 5 23:42:25.043: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up Cust1# *Nov 5 23:42:25.063: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up
Step 4: Verify PPPoE connectivity.
a. Verify that this change resolved the problem and that an IP address has been assigned to the Dialer1 interface.
Cust1# show ip interface brief Interface IP-Address OK? Method Status Protocol Embedded-Service-Engine0/0 unassigned YES unset administratively down down GigabitEthernet0/0 unassigned YES unset administratively down down GigabitEthernet0/1 unassigned YES unset up up Serial0/0/0 unassigned YES unset administratively down down Serial0/0/1 unassigned YES unset administratively down down Dialer1 10.0.0.1 YES IPCP up up Virtual-Access1 unassigned YES unset up up Virtual-Access2 unassigned YES unset up up
b. Display the routing table to verify a route to the ISP router.
Cust1# show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override Gateway of last resort is 0.0.0.0 to network 0.0.0.0 S* 0.0.0.0/0 is directly connected, Dialer1 10.0.0.0/32 is subnetted, 2 subnets C 10.0.0.1 is directly connected, Dialer1 C 10.0.0.254 is directly connected, Dialer1c. Display information about the active PPPoE sessions.
Cust1# show pppoe session 1 client session Uniq ID PPPoE RemMAC Port VT VA State SID LocMAC VA-st Type N/A 1 30f7.0da3.1641 Gi0/1 Di1 Vi2 UP 30f7.0da3.0da1 UP
Step 5: Adjust the maximum segment size on the physical interface.
The PPPoE header adds an additional 8 bytes to each segment. To prevent TCP sessions from being dropped, the maximum segment size (MSS) needs to be adjusted to its optimum value on the physical interface.
a. Display G0/1s configuration setting to see if the MSS has been adjusted.
Cust1# show run interface g0/1 Building configuration... Current configuration : 136 bytes ! interface GigabitEthernet0/1 no ip address duplex auto speed auto pppoe enable group global pppoe-client dial-pool-number 1 end
b. Adjust the MSS to its optimum value of 1452 bytes.
Cust1(config)# interface g0/1 Cust1(config-if)# ip tcp adjust-mss 1452 Cust1(config-if)# end
Reflection
Explain why the TCP segment size needs to be adjusted for PPPoE. ______________________
Answers will vary. The default segment size for Ethernet is 1500. The header information takes up 40 bytes of the segment, leaving 1460 bytes for payload (data). PPPoE requires an additional 8 bytes for its header, so the payload needs to be reduced by 8 bytes to accommodate for the PPPoE header, bringing the optimum maximum segment size down to 1452 bytes.
Router Interface Summary Table
Router Interface Summary | ||||
---|---|---|---|---|
Router Model | Ethernet Interface #1 | Ethernet Interface #2 | Serial Interface #1 | Serial Interface #2 |
1800 | Fast Ethernet 0/0 (F0/0) | Fast Ethernet 0/1 (F0/1) | Serial 0/0/0 (S0/0/0) | Serial 0/0/1 (S0/0/1) |
1900 | Gigabit Ethernet 0/0 (G0/0) | Gigabit Ethernet 0/1 (G0/1) | Serial 0/0/0 (S0/0/0) | Serial 0/0/1 (S0/0/1) |
2801 | Fast Ethernet 0/0 (F0/0) | Fast Ethernet 0/1 (F0/1) | Serial 0/1/0 (S0/1/0) | Serial 0/1/1 (S0/1/1) |
2811 | Fast Ethernet 0/0 (F0/0) | Fast Ethernet 0/1 (F0/1) | Serial 0/0/0 (S0/0/0) | Serial 0/0/1 (S0/0/1) |
2900 | Gigabit Ethernet 0/0 (G0/0) | Gigabit Ethernet 0/1 (G0/1) | Serial 0/0/0 (S0/0/0) | Serial 0/0/1 (S0/0/1) |
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface. |
Device Configs
Cust1# show run Building configuration... Current configuration : 1433 bytes ! version 15.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Cust1 ! enable secret 4 06YFDUHH61wAE/kLkDq9BGho1QM5EnRtoyr8cHAUg.2 ! no aaa new-model ! no ip domain lookup ip cef no ipv6 cef multilink bundle-name authenticated ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 no ip address shutdown duplex auto speed auto ! interface GigabitEthernet0/1 no ip address ip tcp adjust-mss 1452 duplex auto speed auto pppoe enable group global pppoe-client dial-pool-number 1 ! interface Serial0/0/0 no ip address shutdown clock rate 2000000 ! interface Serial0/0/1 no ip address shutdown ! interface Dialer1 mtu 1492 ip address negotiated encapsulation ppp dialer pool 1 ppp authentication chap callin ppp chap hostname Cust1 ppp chap password 0 ciscopppoe ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Dialer1 ! control-plane ! banner motd ^C Unauthorized Access Prohibited. ^C ! line con 0 password 7 14141B180F0B logging synchronous login line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 password 7 05080F1C2243 login transport input all ! scheduler allocate 20000 1000 ! end
ISP# show run Building configuration... Current configuration : 1485 bytes ! version 15.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ISP ! boot-start-marker boot-end-marker ! enable secret 4 06YFDUHH61wAE/kLkDq9BGho1QM5EnRtoyr8cHAUg.2 ! no aaa new-model ! no ip domain lookup ip cef no ipv6 cef multilink bundle-name authenticated ! username Cust1 password 0 ciscopppoe ! bba-group pppoe global virtual-template 1 ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 no ip address shutdown duplex auto speed auto ! interface GigabitEthernet0/1 no ip address ip tcp adjust-mss 1452 duplex auto speed auto pppoe enable group global ! interface Serial0/0/0 no ip address shutdown clock rate 2000000 ! interface Serial0/0/1 no ip address shutdown ! interface Virtual-Template1 ip address 10.0.0.254 255.255.255.0 mtu 1492 peer default ip address pool PPPoEPOOL ppp authentication chap callin ! ip local pool PPPoEPOOL 10.0.0.1 10.0.0.10 ip forward-protocol nd ! no ip http server no ip http secure-server ! control-plane ! banner motd ^C Unauthorized Access Prohibited. ^C ! line con 0 password 7 14141B180F0B logging synchronous login line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 password 7 05080F1C2243 login transport input all ! scheduler allocate 20000 1000 ! end