7.3.2.6 Packet Tracer – Pinging and Tracing to Test the Path (Instructor Version – Optional Packet Tracer)

Addressing Table
Device | Interface | IPv4 Address | Subnet Mask | Default Gateway |
---|---|---|---|---|
IPv6 Address/Prefix | ||||
R1 | G0/0 | 2001:DB8:1:1::1/64 | N/A | |
G0/1 | 10.10.1.97 | 255.255.255.224 | N/A | |
S0/0/1 | 10.10.1.6 | 255.255.255.252 | N/A | |
2001:DB8:1:2::2/64 | N/A | |||
Link-local | FE80::1 | N/A | ||
R2 | S0/0/0 | 10.10.1.5 | 255.255.255.252 | N/A |
2001:DB8:1:2::1/64 | N/A | |||
S0/0/1 | 10.10.1.9 | 255.255.255.252 | N/A | |
2001:DB8:1:3::1/64 | N/A | |||
Link-local | FE80::2 | N/A | ||
R3 | G0/0 | 2001:DB8:1:4::1/64 | N/A | |
G0/1 | 10.10.1.17 | 255.255.255.240 | N/A | |
S0/0/1 | 10.10.1.10 | 255.255.255.252 | N/A | |
2001:DB8:1:3::2/64 | N/A | |||
Link-local | FE80::3 | N/A | ||
PC1 | NIC | 10.10.1.98 | 255.255.255.224 | 10.10.1.97 |
PC2 | NIC | 2001:DB8:1:1::2/64 | FE80::1 | |
PC3 | NIC | 10.10.1.18 | 255.255.255.240 | 10.10.1.17 |
PC4 | NIC | 2001:DB8:1:4::2/64 | FE80::1 |
Objectives
- Part 1: Test and Restore IPv4 Connectivity
- Part 2: Test and Restore IPv6 Connectivity
Scenario
There are connectivity issues in this activity. In addition to gathering and documenting information about the network, you will locate the problems and implement acceptable solutions to restore connectivity.
Note: The user EXEC password is cisco. The privileged EXEC password is class.
Part 1: Test and Restore IPv4 Connectivity
Step 1: Use ipconfig and ping to verify connectivity.
a. Click PC1 and click the Desktop tab > Command Prompt.
b. Enter the ipconfig /all command to collect the IPv4 information. Complete the Addressing Table with the IPv4 address, subnet mask, and default gateway.
c. Click PC3 and click the Desktop tab > Command Prompt.
d. Enter the ipconfig /all command to collect the
IPv4 information. Complete the Addressing Table with the IPv4 address, subnet mask, and default gateway.e. Test connectivity between PC1 and PC3. The ping should fail.
Step 2: Locate the source of connectivity failure.
a. From PC1, enter the necessary command to trace the route to PC3. What is the last successful IPv4 address that was reached?
10.10.1.97
b. The trace will eventually end after 30 attempts. Enter Ctrl+C to stop the trace before 30 attempts.
c. From PC3, enter the necessary command to trace the route to PC1. What is the last successful IPv4 address that was reached?
10.10.1.17
d. Enter Ctrl+C to stop the trace.
e. Click R1 and then the CLI tab. Press ENTER and log in to the router.
f. Enter the show ip interface brief command to list the interfaces and their status. There are two IPv4 addresses on the router. One should have been recorded in Step 2a. What is the other?
10.10.1.6
g. Enter the show ip route command to list the networks to which the router is connected. Note that there are two networks connected to the Serial0/0/1 interface. What are they?
10.10.1.6/32, 10.10.1.4/30
R1#show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 10.0.0.0/8 is variably subnetted, 4 subnets, 3 masks C 10.10.1.4/30 is directly connected, Serial0/0/1 L 10.10.1.6/32 is directly connected, Serial0/0/1 C 10.10.1.96/27 is directly connected, GigabitEthernet0/1 L 10.10.1.97/32 is directly connected, GigabitEthernet0/1
h. Repeat step 2e to 2g with R3 and the answers here.
10.10.1.10; 10.10.1.8/30, 10.10.1.10/32
Notice how the serial interface for R3 changes.
i. Run more tests if it helps visualize the problem. Simulation mode is available.
Step 3: Propose a solution to solve the problem.
a. Compare your answers in Step 2 to the documentation you have available for the network. What is the error
R2’s Serial 0/0/0 interface is configured with the wrong IP address
b. What solution would you propose to correct the problem?
Configure the correct IP address on R2’s Serial 0/0/0 interface (10.10.1.5)
Step 4: Implement the plan.
Implement the solution you proposed in Step 3b.
R2>en R2#show ip interface brief Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES unset administratively down down GigabitEthernet0/1 unassigned YES unset administratively down down Serial0/0/0 10.10.1.2 YES manual up up Serial0/0/1 10.10.1.9 YES manual up up Vlan1 unassigned YES unset administratively down down R2#configure terminal R2(config)#interface serial 0/0/0 R2(config-if)#ip address 10.10.1.5 255.255.255.252 R2(config-if)#exit R2(config)#exit R2#show ip interface brief Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES unset administratively down down GigabitEthernet0/1 unassigned YES unset administratively down down Serial0/0/0 10.10.1.5 YES manual up up Serial0/0/1 10.10.1.9 YES manual up up Vlan1 unassigned YES unset administratively down down
Step 5: Verify that connectivity is restored.
a. From PC1 test connectivity to PC3.
b. From PC3 test connectivity to PC1. Is the problem resolved?
Yes
Step 6: Document the solution.
Part 2: Test and Restore IPv6 Connectivity
Step 1: Use ipv6config and ping to verify connectivity.
a. Click PC2 and click the Desktop tab > Command Prompt.
b. Enter the ipv6config /all command to collect the IPv6 information. Complete the Addressing Table with the IPv6 address, subnet prefix, and default gateway.
c. Click PC4 and click the Desktop tab > Command Prompt.
d. Enter the ipv6config /all command to collect the IPv6 information. Complete the Addressing Table with the IPv6 address, subnet prefix, and default gateway.
e. Test connectivity between PC2 and PC4. The ping should fail.
Step 2: Locate the source of connectivity failure.
a. From PC2, enter the necessary command to trace the route to PC4. What is the last successful IPv6 address that was reached? The trace will eventually end after 30 attempts. Enter Ctrl+C to stop the trace before 30 attempts.
2001:DB8:1:3::2
b. From PC4, enter the necessary command to trace the route to PC2. What is the last successful IPv6 address that was reached?
Enter Ctrl+C to stop the trace. No IPv6 address was reached
c. Click R3 and then the CLI tab. Press ENTER and log in to the router.
d. Enter the show ipv6 interface brief command to list the interfaces and their status. There are two IPv6 addresses on the router. One should match the gateway address recorded in Step 1d. Is there a discrepancy?
Yes
e. Run more tests if it helps visualize the problem. Simulation mode is available.
Step 3: Propose a solution to solve the problem.
a. Compare your answers in Step 2 to the documentation you have available for the network. What is the error
PC4 is using the wrong default gateway configuration
b. What solution would you propose to correct the problem?
Configure PC4 with the correct default gateway address: FE80::3.
Step 4: Implement the plan.
Implement the solution you proposed in Step 3b.

Step 5: Verify that connectivity is restored.
a. From PC2 test connectivity to PC4.
b. From PC4 test connectivity to PC2. Is the problem resolved?
Yes
Step 6: Document the solution.
Suggested Scoring Rubric
