DEMO

Certification Answers

Q. Which two statements about Cisco UCS S3260 Storage Server are true? (Choose two.)

  • A. AMD EPYC 7000 series processors, with up to 32 cores per socket
  • B. Up to 1 TB of Intel Optane DC Persistent Memory
  • C. It is in a compact 2-RU form factor.
  • D. Support for the Cisco 12-G 9460-8i PCle SAS RAID controller
  • E. Massive 840-TB data storage capacity

Q. Which statement is true about SFP?

  • A. SFP modules convert the serial electrical signals to serial analog signals and vice versa.
  • B. The small form-factor pluggable (SFP) is a compact, hot-pluggable copper module transceiver.
  • C. SFP modules offer a simple and effective way to connect a single network device to a wide variety of fiber cable types.
  • D. SFP modules can be classified based on the working voltage and size.

Q. Which two statements about Cisco UCS 6454 Fabric Interconnect are true? (Choose two.)

  • A. 1-RU 10/25/40/100/200/400 Gigabit Ethernet, FCoE, and Fibre Channel switch offers up to 32 ports.
  • B. It hosts and runs Cisco Integrated Management Controller (CIMC).
  • C. All Ethernet ports can support FCoE.
  • D. Provides the management and communication backbone for the Cisco UCS 5108 Server Chassis and Cisco UCS B-Series Blade Servers only.
  • E. Provides both the LAN and SAN connectivity for all servers within its domain.

Q. Refer to the exhibit. What is the name of this Cisco MDS 9700 Series network module?

  • A. Cisco MDS 9700 48-port 16-Gbps switching module
  • B. Cisco MDS 9700 48-port 32-Gbps Fibre Channel switching module
  • C. Cisco MDS 48-Port 10-Gbps Fibre Channel over Ethernet module
  • D. Cisco MDS 24-/10-port SAN Extension module

Q. Which two types of information does the show module NX-OS command display? (Choose two.)

  • A. Module license information
  • B. Module ports type
  • C. Module IP address
  • D. Module type
  • E. Module status

Q. Which two provide connectivity to Fabric Extenders? (Choose two.)

  • A. UCS 6300 series
  • B. UCS B-Series Servers
  • C. UCS 6400 series
  • D. UCS S-Series Storage Servers
  • E. UCS E-Series Servers

Q. Which two form factors are available in the Cisco UCS E-Series Servers? (Choose two.)

  • A. EHWIC
  • B. PVDM
  • C. NIM
  • D. VIC
  • E. WIC

Q. Which command-line interface mode is best described by this prompt? Switch (config) #

  • A. Local management mode
  • B. EXEC mode
  • C. Boot mode
  • D. Global configuration command mode

Q. What are the two layers in the SAN hierarchy? (Choose two.)

  • A. Protocol layer
  • B. Fabric layer
  • C. Connection layer
  • D. Switch layer
  • E. Storage layer

Q. Which two blade servers support GPUs? (Choose two.)

  • A. UCS B260 M4
  • B. UCS B200 M4
  • C. UCS B420 M4
  • D. UCS B480 M5
  • E. UCS B200 M5

Q. Which two statements about PCIe are true? (Choose two.)

  • A. The PCle supports native hot-swap functionality.
  • B. You can install a PCI Express x16 adapter into an x4 slot.
  • C. The PCIe standard is a bus-based system in which all the devices share the same bidirectional, 32-bit or 64-bit, parallel signal path.
  • D. The PCIe 4.0 standard doubles the transfer rate compared to PCIe 5.0.
  • E. A link that is composed of four lanes is called an x4 link.

Q. Which statement about RAID is true?

  • A. RAID is a scheme used to logically combine several independent disks to form an array or group of drives.
  • B. RAID provides data redundancy with either odd parity or even parity.
  • C. RAID drive group appears to the host computer as multiple physical storage units.
  • D. RAID parity information can be stored across multiple RAID levels.
  • E. RAID stores data in the array with data striping, encryption, and parity to organize the data among the disks.

Q. Which type of optics module is supported by a Cisco Nexus 7700 F4-Series 30-Port 100-Gigabit Ethernet Module?

  • A. QSFP28
  • B. SFP+
  • C. Cisco CPAK
  • D. QSFP+

Q. Refer to the exhibit. Which item does C represent?

  • A. CMOS Battery
  • B. Internal USB
  • C. Mini Storage Connector
  • D. mLOM Connector
  • E. GPU

Q. Refer to the exhibit. Which statement correctly identifies the hardware features on the Cisco Nexus 9500 Series supervisor A modules?

  • A. A is 10/100/1000 Management port; B is USB port; C is Console port; D is external clock input
  • B. A is Console port; B is USB port; C is 10/100/1000 Management port; D is external clock input
  • C. A is Optical port; B is USB port; C is 10/100/1000 Management port; D is external clock input
  • D. A is Console port; B is USB port; C is 10/100/1000 Management port; D is Diagnostic port

Q. Which two statements about the Ethernet media are true? (Choose two.)

  • A. A twisted-pair cable system has each pair of wires twisted together to reduce electromagnetic interference.
  • B. Compared to multimode fiber, the single-mode fiber is designed for shorter distances with higher cost.
  • C. 40 Gigabit Ethernet twinax cables deploy Enhanced Quad Small Form Factor Pluggable (QSFP+) connectors.
  • D. The twinax cables can be found in either a shielded twisted-pair or an unshielded twisted-pair variation.
  • E. A passive twinax cable can carry an Ethernet signal over 5m.

Q. Which two commands allow you to view the state of high availability between the two clustered Fabric Interconnects? (Choose two.)

  • A. show cluster state extended
  • B. show cluster extended-state
  • C. show cluster HA status
  • D. show cluster state
  • E. show cluster HA state

Q. When activating the firmware via UCSM which two firmware versions must be activated at the same time?

  • A. UCS Manager and System
  • B. UCS Manger and Kernel
  • C. CIMC and Kernel
  • D. System and Kernel

Q. In Cisco UCS C480 M5 server, which PCle slot is the default slot for the rear RAID controller when the rear drive module is used with SAS/SATA drives?

  • A. PCle slot 09
  • B. PCle slot 10
  • C. PCle slot 11
  • D. PCle slot 12

Q. Which two transceivers can support 100 Gigabit Ethernet? (Choose two.)

  • A. SFP+
  • B. SFP28
  • C. QSFP+
  • D. QSFP28
  • E. SFP-DD

Q. What are two common steps to troubleshooting a rack server with unrecognized or memory errors? (Choose two.)

  • A. Ensure DIMMs are installed in correct slots
  • B. Check CPU sockets for bent pins
  • C. Check that the AC power cord is OK
  • D. Reseat DIMMs
  • E. Check the front I/O cable connection to the motherboard

Q. Which Cisco UCS Virtual Interface Card Series is designed exclusively for the M5 generation?

  • A. M81KR VIC
  • B. VIC 1400 Series
  • C. VIC 1300 Series
  • D. VIC 1200 Series

Q. Which command syntax is correct to reset the admin password when the switch is in the kickstart prompt? switch(boot) #”

  • A. exec -> admin-password
  • B. connect local-mgmt -> admin-password
  • C. configure terminal -> admin-password
  • D. connect nxos -> admin-password
  • E. admin-password

Q. Which statement about the Cisco Nexus 3408-S switch is true?

  • A. It is offered in a three-rack-unit (3-RU) form factor.
  • B. It supports 200G or 400G line card expansion modules.
  • C. It has dual-redundant power supplies.
  • D. It is 4-slot chassis with 400G line card expansion modules.

Q. What enables NVM Express host software to communicate with nonvolatile memory?

  • A. SATA
  • B. SAS
  • C. PCle
  • D. SCSI

Q. Which two virtualization technologies are used in a modern data center design? (Choose two.)

  • A. Storage virtualization
  • B. Cloud virtualization
  • C. Platform virtualization
  • D. Server virtualization
  • E. Application virtualization

Q. What is the name of the process to automatically upgrade a new Fabric Interconnect when it is connected to the functioning Fabric Interconnect?

  • A. Firmware Policy Process
  • B. Auto-Negotiate Process
  • C. Auto-Sync Process
  • D. Firmware Update Process

Q. Which tool is needed when servicing a UCS M5 server?

  • A. PCle slot cover
  • B. T-30 Torx driver
  • C. M5 DIMM puller
  • D. HDD removal tool

Q. When replacing a standalone C-Series server which order will be used to shut down the server via CIMC?

  • A. Click Power off, Click Shut off
  • B. Click Power off, Click Shut down
  • C. Click Host power, Click Shut off
  • D. Click Host power, Click Shut down

Q. What is Platform as a Service?

  • A. It configures, manages and develops networking environment for your application.
  • B. It is when an application service is delivered over the network on a subscription basis.
  • C. It is where servers and virtual machines (VMs), network and storage are delivered over the network on a pay-as-you-go basis.
  • D. It is the software development framework and components delivered over the network on a pay-as-you-go basis.

Q. Which statement is true about cloud computing?

  • A. It provides self-service, on-demand provisioning and a billing for corporate usage only.
  • B. Users usually own and maintain their own IT infrastructure and facility.
  • C. It provides end-to-end server, application network service, and storage virtualization.
  • D. It increases total cost of ownership.

Q. In the Cisco UCS S3260 Storage Server which two of the below ports are available on a System I/O Controller? (Choose two.)

  • A. Dedicated Management port
  • B. PCle ports
  • C. KVM Console port
  • D. QSFP port
  • E. Ethernet LOM port

Q. Which two cable types can support 10Gbps speed? (Choose two.)

  • A. CAT7
  • B. CAT5a
  • C. CAT5e
  • D. CAT6a
  • E. CAT5

Q. Refer to the exhibit. Which item does C represent?

  • A. Pin icon (prevents Navigation pane from sliding)
  • B. Icon to view the Navigation pane
  • C. Favorite Icon (make any specific work pane in the application as your favorite)
  • D. Index Icon (view listing in alphabetical order)

Q. What is the command to provide details pertaining to the state of the cluster?

  • A. Show cluster
  • B. Show cluster extended-state
  • C. Show cluster state
  • D. Show extended cluster state

Q. Which two specialized tools do you need to service a UCS product? (Choose two.)

  • A. Laptop
  • B. Anti-static Strap
  • C. KVM Console to USB 2.0 Portable Laptop Crash Cart
  • D. Cable Tester
  • E. Needle-nose pliers

Q. Which group of UCS Virtual Interface Cards is exclusively designed for Cisco UCS C-Series Rack Server?

  • A. VIC 1455, VIC 1480, VIC 1385, VIC 1340, VIC 1280
  • B. VIC 1440, VIC 1340, VIC 1388, VIC 1280, M81KR VIC
  • C. M81KR VIC, VIC 1497, VIC 1340, VIC 1387, VIC 1240
  • D. VIC 1455, VIC 1497, VIC 1385, VIC 1387, VIC 1225

Q. To confirm the installation of a B-Series Server, which GUI based management tool will be used?

  • A. Windows 10
  • B. UCSM (UCS Manager)
  • C. Console Access
  • D. CIMC (Cisco Integrated Management Controller)

Q. Cisco UCS 5100 Blade Server Chassis supports which two devices? (Choose two.)

  • A. Blade servers
  • B. Fiber Extenders
  • C. Rack-mount Servers
  • D. S-Series Storage servers
  • E. E-Series Servers

Q. DRAG DROP Refer to the diagram, match the following Ethernet frame fields. Select and Place:

ANSWER:

Q. DRAG DROP

Refer to the exhibit. Match the Fault Icons to the appropriate description. Select and Place:

ANSWER:

Q. DRAG DROP Drag the cable or connector on the left to the correct interface on the right. Select and Place:

ANSWER:

Q. DRAG DROP Drag the password recovery procedures on a Cisco NX-OS switch from the left to the right and place them in order. Select and Place:

ANSWER:

Q. Which three steps do you perform to troubleshoot when a rack server powers on with no video? (Choose three.)

  • A. Check that the front I/O dongle is properly seated.
  • B. Check the front I/O cable connection to the motherboard.
  • C. Check for memory subsystem failure.
  • D. Verify the power source to equipment.
  • E. Reseat the DIMMs, CPU, and PCI cards.

Q. What is the maximum number of supervisor modules that the Cisco MDS 9710 Switch supports?

  • A. 1
  • B. 2
  • C. 4
  • D. 6
  • E. 8

Q. Which device provides analysis of Fibre Channel traffic without any network disruption?

  • A. Cisco MDS 9000 Data Analyzer Adapter
  • B. Cisco MDS 9000 Port Analyzer Adapter
  • C. Cisco MDS 9000 Channel Analyzer Device
  • D. Cisco MDS 9000 Channel Analyzer Adapter

Q. Refer to the exhibit.

What is the name of this Cisco Nexus 3000 Series Switch?
  • A. Cisco Nexus 3132Q
  • B. Cisco Nexus 3172PQ
  • C. Cisco Nexus 3524
  • D. Cisco Nexus 3016

Q. Which two Cisco Nexus switches provide the foundation of the Cisco Application Centric Infrastructure? (Choose two.)

  • A. Cisco Nexus 7718 switch
  • B. Cisco Nexus 9508 switch
  • C. Cisco Nexus 7710 switch
  • D. Cisco Nexus 93128TX switch
  • E. Cisco Nexus 6004 switch

Q. Which type of optics module is supported by a 6-port 40 GE Cisco Nexus 7000 M2 Series I/O module?

  • A. CPAK
  • B. QSFP+
  • C. SFP/SFP+
  • D. CFP

Q. How many 10GBASE-T port licenses are preinstalled on a Cisco Nexus 3064-32T?

  • A. 16
  • B. 32
  • C. 48
  • D. 64

Q. Refer to the exhibit.

Which three options are features of the Cisco UCS 6248UP Fabric Interconnect front panel? (Choose three.)
  • A. Console port
  • B. FCoE port
  • C. 10 Gb/s port
  • D. Fan module
  • E. USB port

Q. Which two statements about the Cisco Nexus 5596UP switch are true? (Choose two.)

  • A. Its power supplies and fan trays are hot-swappable.
  • B. It supports unified ports.
  • C. It is offered in a one-rack-unit form factor.
  • D. It has one expansion slot.
  • E. It supports up to 96 10G BASE-T ports.

Q. When a host firmware package policy is created, what must it be associated with to upgrade the BIOS?

  • A. blade or blade pool
  • B. service profile
  • C. boot policy
  • D. service template

Q. Up to what speed can Category 5 UTP cable transmit data?

  • A. 10 Mb/s
  • B. 100 Mb/s
  • C. 1000 Mb/s
  • D. 10000 Mb/s

Q. Up to what speed can Category 5e UTP cable transmit data?

  • A. 10 Mb/s
  • B. 100 Mb/s
  • C. 1000 Mb/s
  • D. 10000 Mb/s

Q. What is the maximum distance that the 40GBASE-LR4 Ethernet standard can span?

  • A. 550 m
  • B. 10 km
  • C. 40 km
  • D. 80 km

Q. On which three devices can the Host Upgrade Utility be performed? (Choose three.)

  • A. C420
  • B. C230
  • C. B230
  • D. B210
  • E. C210
  • F. B460

Q. Refer to the exhibit.

This image shows a CPU Pick-and-Place tool and a CPU Socket Protective Cap Removal tool. Which types of Cisco UCS servers and Intel Xeon processors do these tools support?
  • A. Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2400 Series processors
  • B. Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2600 Series processors
  • C. Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2400 Seriesprocessors
  • D. Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2600 Seriesprocessors

Q. Which three troubleshooting procedures do you perform when there is no power to a Cisco UCS B250 M2 Blade Server? (Choose three.)

  • A. Decommission and acknowledge the blade.
  • B. Check the back of the blade to ensure that there is no damage to the connection that goes into chassis.
  • C. Reseat the memory DIMMs.
  • D. Check the CPU sockets for bent pins.
  • E. Reseat the blade in the same slot in the chassis.
  • F. Move the blade to another slot in the chassis.

Q. Which two remote file system methods are used in the training material to transfer firmware to the Fabric Interconnect? (Choose two.)

  • A. FTPS
  • B. FTP
  • C. TFTP
  • D. RSH

Q. Which three tools are necessary to console into a Cisco UCS C-Series Rack-Mount Server? (Choose three.)

  • A. Cisco DB-9-to-RJ-45 console cable
  • B. laptop
  • C. monitor
  • D. keyboard
  • E. KVM dongle
  • F. USB serial adapter

Q. After installation or replacement of a Cisco UCS C-Series Rack-Mount Server, the host does not boot. Which four options should be verified? (Choose four.)

  • A. Verify the power source to the equipment.
  • B. Check for loose HDD cables.
  • C. Reseat the DIMMs, CPU, and PCI cards.
  • D. Verify that power supplies are receiving power.
  • E. Reseat the mezzanine card connector.
  • F. Check the CPU sockets for bent pins.

Q. Which three firmware components does the Host Upgrade Utility upgrade? (Choose three.)

  • A. Fabric Interconnect firmware
  • B. LAN on Motherboard
  • C. Cisco UCS Manager
  • D. CIMC
  • E. System BIOS

Q. Which three components are hot swappable in a Cisco UCS Blade Server and Chassis? (Choose three.)

  • A. Fabric Extender
  • B. Power supply
  • C. Heat sink
  • D. SAS Hard Drive
  • E. 2x8GB Kit DIMMs
  • F. Mezzanine card

Q. Which five things should the administrator verify after performing maintenance or replacing a blade server? (Choose five.)

  • A. blade server status
  • B. hard drive status
  • C. host OS boot status
  • D. CPU status
  • E. mezzanine card status
  • F. memory DIMM status

Q. Which two statements about DIMM replacement in Cisco UCS Servers are true? (Choose two.)

  • A. In blade servers, DIMMs can be installed in either 1, 2, 4, or 8 DIMMs per channel.
  • B. Rack-mount and blade servers have memory fault LEDs that indicate which DIMM requires attention.
  • C. In servers that require pairs of DIMMs, the pairs must be identical (manufacturer, size, part #, and so on).
  • D. If the memory in a server is not fully populated, you can install DIMMs in any open slot.

Q. Which action should the administrator take before physically removing a blade server for maintenance or replacement?

  • A. Force the server to shut down.
  • B. Disassociate the service profile.
  • C. Decommission the server.
  • D. Perform a graceful shutdown of the server.

Q. Which three statements about powering down a Cisco UCS C-Series Rack-Mount Server to perform maintenance or replacement are true? (Choose three.)

  • A. Standby power mode: Power is supplied only to the service processor and the cooling fans, and it is safe to power off the server from this mode.
  • B. Power status LE
  • C. Green indicates that the server is in main power mode and can be safely powered off.
  • D. Graceful shutdown: Press and release the power button. The operating system performs a graceful shutdown, and the server goes to standby mode, which isindicated by an amber power status LED.
  • E. Disconnect the power cords from the power supplies in your server to completely power off the server.
  • F. Only an emergency shutdown can be performed using the power button on the server front panel.

Q. Which tool does a network administrator not need when installing hardware?

  • A. cable tester
  • B. wrench set
  • C. cable wraps
  • D. needle-nose pliers
  • E. PCMCIA memory
  • F. soldering iron with grounded tip

Q. When the Cisco UCS Manager is used to verify the B- or C-Series device, which two types of Overall Status are acceptable and do not indicate a failure? (Choose two.)

  • A. Online
  • B. OK
  • C. Unassociated
  • D. Active

Q. What is the correct path to verify the Overall Status of Chassis 1 | Server 3?

  • A. Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 Status tab
  • B. Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 General tab
  • C. Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 FSM tab
  • D. Servers Tab > Chassis > Server 3 General tab
  • E. Status Tab > Chassis > Chassis 1 > Servers > Server 3
  • F. Admin Tab > Chassis > Chassis 1 > Servers > Server 3 General tab

Q. If the Overall Status for a Cisco UCS B-Series Blade Server indicates a failure in the Cisco UCS Manager, such as discovery-failed, which statement is true?

  • A. The server shuts down.
  • B. The server automatically reboots reboot in 3 minutes.
  • C. The endpoints on that server cannot be upgraded.
  • D. The server is online, but the administrator cannot assign a service profile to that blade.

Q. Which two commands display the version of Cisco NX-OS code that the device is currently running on? (Choose two.)

  • A. show version
  • B. show module
  • C. show interface
  • D. show boot
  • E. show license

Q. On the Sensors page from the CIMC view, which four tabs are displayed to view further information? (Choose four.)

  • A. Power Supply
  • B. Fan
  • C. Memory
  • D. CPU
  • E. LEDs
  • F. Temperature

Q. Which three options are the minimum browser requirements to log into the Cisco CIMC GUI? (Choose three.)

  • A. Java 1.6 or higher
  • B. HTTP and HTTPS enabled
  • C. Adobe Flash Player 10 or higher
  • D. Internet Explorer version 10
  • E. Firefox 26.0
  • F. Adobe Shockwave Player 11 or higher

Q. To do a password recovery on a Cisco NX-OS Switch, which option shows the correct syntax to display the bootflash contents at the switch(boot)#?

  • A. display bootflash:
  • B. show bootflash:
  • C. dir bootflash:
  • D. find bootflash:

Q. Which Cisco NX-OS command displays kernel uptime?

  • A. show module
  • B. show version
  • C. show license
  • D. show boot
  • E. show interface

Q. Refer to the exhibit.

Which option should you select to get the output of the show tech-support detail command for the Cisco UCS B-Series blade?
  • A. A – ucsm
  • B. B – chassis
  • C. C – fabric-extender
  • D. D – rack-server

Q. Refer to the exhibit.

Where is the best place to see the power supply status of the blade server enclosure?
  • A. A – Chassis 1
  • B. B – Chassis 1 – PSUs
  • C. C – Chassis1 – Servers
  • D. D – Rack-Mounts – Servers
  • E. E – Fabric Interconnects A – PSUs

Q. Refer to the exhibit.

Where is the best place to find the B200 BIOS version used in a specific Cisco UCS Manager version?
  • A. A – Installed Firmware
  • B. B – Packages
  • C. C – Images
  • D. D – Capability Catalog
  • E. E – Management Extension

Q. Which command saves the active configuration to NVRAM?

  • A. copy startup-config running-config
  • B. copy active-config backup-config
  • C. copy running-config startup-config
  • D. copy backup-config active-config

Q. Refer to the exhibit.

Where is the best place to see bootflash free space?
  • A. A – Available Memory
  • B. B – Total Memory
  • C. C – Local Storage Information
  • D. D – High Availability Details

Q. Which command-line interface mode is best described by this prompt? UCS-switch-A (nxos)#

  • A. maintenance mode
  • B. EXEC mode
  • C. local management mode
  • D. global configuration mode
  • E. Cisco IOS mode

Q. Which command can be used to exit to EXEC mode from this current mode? switch(config-if) #

  • A. Ctrl-C
  • B. Ctrl-L
  • C. quit
  • D. exit
  • E. end

Q. Refer to the exhibit.

Where is the best place to see whether the system is ready for a Fabric Interconnect failover?
  • A. A – Overall Status operable
  • B. B – L1 Connection
  • C. C – Part Details
  • D. D – Access
  • E. E – High Availability Details

Q. Refer to the exhibit.

Which item does A represent?
  • A. Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
  • B. Virtual Interface Card for Cisco UCS B420 M3 Blade Servers
  • C. mLOM for Cisco UCS B420 M3 Blade Servers
  • D. Virtual Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers
  • E. SuperCap module for Cisco UCS B420 M3 Blade Servers

Q. Refer to the exhibit.

Which call-out accurately shows the current running version of the Cisco UCS Manager management software?
  • A. A – UCS Manager running version 1.4(1m)
  • B. B – IO Module 1 running version 1.4(1m)
  • C. C – Interface Card 1 running version 1.4(1m)
  • D. D – Kernel running version 4.2(1)N(1.4m)

Q. Which supervisor module is supported by a Cisco Nexus 7700 Series Switch?

  • A. first-generation supervisor module
  • B. second-generation supervisor module (Sup2)
  • C. second-generation supervisor enhanced module (Sup2E)
  • D. third-generation supervisor enhanced module (Sup3E)

Q. Which type of optics module is supported by a 12-port 100 GE Cisco Nexus 7700 F3 Series I/O module?

  • A. CPAK
  • B. QSFP+
  • C. SFP/SFP+
  • D. CFP

Q. Refer to the exhibit.

Which Cisco MDS chassis supports the 48-Port 16-Gbps Fibre Channel Switching Module?
  • A. MDS 9509
  • B. MDS 9513
  • C. MDS 9710
  • D. MDS 9506

Q. Refer to the exhibit.

What is the name of this rack-mount server?
  • A. Cisco UCS C220 Rack-Mount Server
  • B. Cisco UCS C240 Rack-Mount Server
  • C. Cisco UCS C420 Rack-Mount Server
  • D. Cisco UCS C460 Rack-Mount Server

Q. Which two major components does a Cisco Nexus 1000V Series Switch have? (Choose two.)

  • A. Virtual Fiber Channel Module
  • B. Virtual Ethernet Module
  • C. Virtual Supervisor Module
  • D. Virtual Memory Controller Module
  • E. Virtual Network Module

Q. Which Cisco Nexus 5000 Series model supports 1/10G BASE-T ports?

  • A. Cisco Nexus 5548P
  • B. Cisco Nexus 5548UP
  • C. Cisco Nexus 5596UP
  • D. Cisco Nexus 5596T

Q. Which Cisco MDS model supports the most Fibre Channel ports per chassis?

  • A. MDS 9513
  • B. MDS 9509
  • C. MDS 9506
  • D. MDS 9250i

Q. Refer to the exhibit. Which statement correctly identifies the front panel LEDs on the Cisco UCS C220 Server?

  • A. A is power button and power status LED; B is identification button and LED; C is system status LED; D is network link activity LED.
  • B. A is network link activity LED; B is system status LED; C is power button and power status LED; D is identification button and LED.
  • C. A is system status LED; B is network link activity LED; C is power button and power status LED; D is identification button and LED.
  • D. A is network link activity LED; B is system status LED; C is identification button and LED; D is power button and power status LED.

Q. Which processor option is supported in the Cisco UCS C420 M3 Server?

  • A. up to two Intel Xeon E5-4600 series multicore processors
  • B. up to two Intel Xeon E7-4800 series multicore processors
  • C. up to four Intel Xeon E5-4600 series multicore processors
  • D. two or four Intel Xeon E7-8800 series multicore processors

Q. How do you find the serial number of a Cisco UCS 5108 Blade Server chassis?

  • A. Use the Cisco UCS Admin.
  • B. Use the Cisco UCS Application.
  • C. Use the Cisco UCS Assistant.
  • D. Use the Cisco UCS Manager.

Q. What does the system status LED look like when an over temperature or major alarm occurs on the Cisco UCS 6120XP Fabric Interconnect?

  • A. Amber
  • B. Red
  • C. Blinking amber
  • D. Blinking red

Q. Refer to the exhibit. Which item does F represent?

  • A. HDD 1
  • B. TFP Module
  • C. SuperCap Module
  • D. CPU 2
  • E. CMOS Battery

Q. Which three statements about FCoE are true? (Choose three.)

  • A. Allows Fibre Channel and Ethernet networks to share a single, integrated infrastructure.
  • B. Encapsulates Fibre Channel frames into Ethernet frames, which allows them to run alongside traditional IP traffic.
  • C. Increases capital costs due to the difficulty to manage.
  • D. Consolidates I/O traffic in the data center.

Q. Which cable is used to access the command-line interface of a Cisco UCS 6120XP Fabric Interconnects?

  • A. KVM cable
  • B. console cable
  • C. Ethernet cable
  • D. SFP+ Ethernet transceiver cable

Q. Where do you find the model number of a Cisco MDS 9200 Series chassis?

  • A. on the top front of the chassis next to the serial number
  • B. on the bottom front of the chassis next to the Cisco logo
  • C. on the top front of the chassis next to the Cisco logo
  • D. on the bottom front of the chassis next to the serial number

Q. Which fiber optic cable type is used most often with a Subscriber connector?

  • A. dual-mode
  • B. single-mode
  • C. straight-mode
  • D. multi-mode
  • E. subscriber-mode

Q. Which type of connection across the network does a SAN allow for multiple servers to access an unlimited amount of storage devices?

  • A. any-to-many
  • B. many-to-any
  • C. any-to-any
  • D. any-to-one
  • E. one-to-any

Q. What is the wire transmission speed for 100GBASE-ER4 Ethernet?

  • A. 100 Mb/s
  • B. 1 Gb/s
  • C. 10 Gb/s
  • D. 100 Gb/s

Q. Which two statements about PCIe are true? (Choose two.)

  • A. The PCIe link is built around dedicated unidirectional couples of serial, point-to-point connections known as lanes.
  • B. You can install a PCI Express x8 adapter into an x4 slot.
  • C. The PCIe standard is a bus-based system in which all the devices share the same bidirectional, 32-bit or 64-bit, parallel signal path.
  • D. The PCIe 1.0 standard doubles the transfer rate compared to PCIe 2.0.
  • E. A link that is composed of four lanes is called an x4 link.

Q. Which method does FCIP use to enable connectivity of geographically distributed Fibre Channel SANs over IP?

  • A. routing
  • B. tunneling
  • C. handshaking
  • D. transporting

Q. Which important feature on the front end is provided to the clients by multiple servers that access the same storage devices across the SAN?

  • A. recovery
  • B. redundancy
  • C. resiliency
  • D. security
  • E. storage

Q. The Ethernet specification details several different fiber optic media types. What is the wire transmission speed for 100BASE-FX Ethernet?

  • A. 10 Mb/s
  • B. 100 Mb/s
  • C. 1000 Mb/s
  • D. 10000 Mb/s

Q. Which method is a TCP/IP-based protocol for establishing and managing connections between IP-based storage devices, hosts, and clients?

  • A. FCIP
  • B. iFCP
  • C. iSCSI
  • D. FCoE